|
Ford AU Series 1 to AU Series 3 Falcon, XR, Fairmont, Fairlane, LTD and Ute Instrument Cluster Diagnostic Mode |
A big thankyou goes to AU2SR - Aka Jeff for Finding this bit of hideen information, and for allowing Fordmods to host this document !
This document describes the Falcon AU Dash Diagnostic Information that is provided when the Dash is placed in Diagnostic mode
The information that is returned is displayed using the Odometer display area, and includes the information that is transferred on the ECU bus
This includes Fuel level, Fuel consumption, oil pressure, Coolant Temperature, RPM, Vehicle speed, Gear lever position, Door Ajar, and many others
|
|
Entering Diagnostic mode |
The diagnostic mode can be entered by using the following method
1) With the ignition key in the off position, turn the Ignition Key to the On Position.
2) Using the Odometer Button, Press the Odometer Button Down, then release 5 Times within 10 Seconds (Note : You must be very accurate with the timing. Depress the Button for 1 second, then release for 1 second. Do this 5 Times in 10 seconds)
3) Release the Odometer Button for 5 seconds.
4) Depress the Odometer Button for 7 Seconds.
5) Release the Odometer Button for 5 Seconds.
6) Depress the Odometer Button for 7 Seconds.
You should now be within the AU Instrument Cluster Diagnostic Mode
Within Diagnostic mode, there are 19 Diagnostic Screens that are available.
At the moment we do not have enough information as to what all the screens actually are.
To Exit the Diagnostic mode, Depress the Odometer Button for 11 seconds.
More Information will be made available as to what diagnostic sections display what type of information soon !
|
|
Diagnostic Codes |
| Mode |
Top Line |
Bottom Line |
| 1 |
Petrol in Litres (No Level Buffering) |
Petrol Sender Resistance (Unbuffered) |
| 2 |
|
Coolant Temperature (Degrees C) |
| 3 |
Engine RPM |
Vehicle Speed (KM/H) |
| 4 |
Oil Pressure (Bar, 1 decimal Point) |
Battery Voltage (Volts) |
| 5 |
Instant Fuel Consumption (L/100Km) |
Instant Fuel Consumption (x 0.1 Litres) |
| 6 |
Fuel used since Trip Avg L/100 Reset (x 0.1L)
This Value is used to calculate the Trip computer Average Fuel consumption L/100Km |
Kms Travelled since Trip Avg L/100 Reset |
| 7 |
Buffered Fuel Tank Level (In Litres)
Value used for Petrol Gauge |
Buffered Fuel Tank Lever Sender Resistance |
| 8 |
|
Gear Position (PNRD321) |
| 9 |
Unknown - 0000 |
Unknown - 1111 Changes on AC Clutch Engage |
| 10 |
Unknown - 0000 |
Unknown - 1111 |
| 11 |
Unknown - 0000 |
Unknown - 1111 |
| 12 |
Unknown - 0 |
|
| 13 |
Unknown - 0 |
|
| 14 |
Unknown - 0000 |
118 |
| 15 |
Unknown - 0000 |
255 |
| 16 |
98 |
112 |
| 17 |
Unknown - 0 |
0 |
| 18 |
-o-d ---- |
|
|
|
Police - (Ex Chaser) Instrument Clusters |
In addition to the above diagnostic modes, the Police (Chaser) Instrument clusters also have a Speedo Calibration mode.
The Police (Ex-Chaser) instrument cluster allows re-programming of the Speedo Reading, (and consequently the Odometer), so as a Precise Speedo Reading can be made.
This also means that the Speedo can be re-calibrated, when making changes to the Factory fitted wheels, Tyre Profiles, as well as altering differential Ratios.
To determine if you have a Police (Ex Chaser) Instrument Cluster fitted, try the following Routine, to enter the calibration mode.
To Calculate Calibration figures for the Police Instrument cluster, when making the above modifications, please check the
Diff and Tyre Calculator Page.
Warning : Playing with the Instrument Calibration feature will modify your Speedo, and Odometer readings.
Please be sure of the consequences of changing these settings, and also Make note of your Original Calibration Setting
This will ensure that you can return the Speedo Calibration Back to its original condition, if modified.
Entering the Police Instruments Calibration Mode - (Police AU Series I models)
1) With the ignition key in the On position, press and hold the Odometer reset knob for 5 seconds, then release.
2) The Odometer will then display "SPEEDO #.#" - where #.# is the Speedo calibration Percentage, and is set to "0.0" Percent from the factory.
3) To increase the Percentage adjustment, Press the Odometer reset shaft for a short period of time (0.2 to 0.7 seconds). This will increase the adjustment by 0.5%
4) To decrease the Percentage adjustment, Press the Odometer reset shaft for a long period of time (0.8 to 4.9 seconds). This will decrease the adjustment by 0.5%
5) To exit the Speedo calibration mode, press and hold the Odometer Reset shaft for a period longer than 5 seconds.
Entering the Police Instruments Calibration Mode - (Police AU Series II - AUIII Models)
1) With the ignition key in the Off position, press and hold the Odometer reset knob
2) Turn the Ignition Switch On, and continue to hold the Reset shaft in for 5 seconds, until the cluster enters calibration mode, (Typically 5 seconds)
2) The Odometer will then display "SPEEDO #.#" - where #.# is the Speedo calibration Percentage, and is set to "0.0" Percent from the factory.
3) To increase the Percentage adjustment, Press the Odometer reset shaft for a short period of time (0.2 to 0.7 seconds). This will increase the adjustment by 0.5%
4) To decrease the Percentage adjustment, Press the Odometer reset shaft for a long period of time (0.8 to 4.9 seconds). This will decrease the adjustment by 0.5%
5) To exit the Speedo calibration mode, press and hold the Odometer Reset shaft for a period longer than 5 seconds.
|
|
